Superior Blower FAB 1100 User Manual

HEARTH PRODUCTS  
KITS AND ACCESSORIES  
FORCED AIR BLOWER KIT  
FAB-1100  
P/N 903249  
REV. E 11/2004  
INSTALLATION INSTRUCTIONS FOR BLOWER KIT  
MODEL FAB-1100  
GENERAL INFORMATION  
Magnets  
The FAB-1100 forced air blower kit consists of a 105 CFM dual  
blower assembly.  
Blower  
in Position  
The blower supplies air delivery at 105 CFM at 0" H2O static pressure,  
90 CFM at 0.2" H2O static pressure. The maximum operating static  
pressure is 0.38" H2O.  
Magnets  
The FAB-1100 has been tested and certified by CSA.  
Always check local building codes. The installation must comply with  
local regulations as well as the National Electric Code.  
Make Entry where No Obstructions are Present.  
Failure to follow these instructions could cause a fireplace malfunc-  
tion resulting in possible injury and/or property damage.  
Figure 1  
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
PRELIMINARY INSPECTION  
Outlet  
Plenums  
Remove the blower kit from the carton and check for any damage.  
Check inventory: blower assembly, sleeved power cord and installa-  
tion instructions.  
INSTALLING THE BLOWER  
Step 1. In most appliances the FAB-1100 blower is simply posi-  
tioned against the appliance back wall, with the magnets engaging  
the sheetmetal rear wall to secure the blower in place. Generally  
access to this location is gained by the opening (or removal) of the  
appliance lower compartment door of louvers Figure 1.  
FAB-1100  
Blower  
Blower  
Base  
Figure 2  
Step 2. The blower is properly positioned when it is centered against  
the appliance rear wall with the outlet plenums pointed upwards  
(Figure 2 ). Ensure that the blower base is firmly seated on the  
appliance base. Ensure that the blower is positioned against the  
appliance back wall. Some appliances are fitted with a blower shield  
preventing access to the back wall of the appliance. In this case  
remove the shield, place the blower, complete its installation, then  
replace the shield.  
Note: The FAB-1100 may also be used with the PureHeat appliance and  
the CGI-BAY and GI-3821 gas inserts. For use with the PureHeat and  
CGI-BAY appliances follow the instructions in their installation docu-  
ments and those found in the PHEXK and CBEK kits respectively. The  
FAB-1100 is installed in the GI-3821 in accordance with instructions  
provided with that appliance.  
Step 3. Route the blower sleeved power cord to a switched, standard  
grounded three pronged outlet mounted on the appliance internal "J"  
box cover plate prewired at the time of appliance installation (see page  
2 of this document, Figure 3 ). Ensure power cord minimizes contact  
with hot appliance surfaces. Operate the FAB-1100 from the switch  
controlling power to the appliance junction box.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
 

Shark Pressure Washer SSG 503027E SSG 503027G SSG 503537E SSG 503537G SSG 603537E SSG 603537G User Manual
Soleus Air Air Conditioner GL PAC 08E4 User Manual
Sony Car Stereo System CDX R3350 User Manual
Sony Car Stereo System XR CA665EE User Manual
Sony CD Player CDP CX571 User Manual
Sony Switch 4 296 436 11 2 User Manual
Stamina Products Exercise Bike 15 0135 User Manual
StarTechcom Power Supply ATXPOW350DF User Manual
SUPER MICRO Computer Computer Hardware Super PIIIDM3 User Manual
SUPER MICRO Computer Network Card 5014C T User Manual